
Wie baue ich einen D/A Konverter fr die parallele Schnittstelle ??



    Die hier beschriebenen D/A Konverter werden von CREATOR 3.00
    MP, WOW und anderen untersttzt.


    1. Ein einfacher D/A Konverter fr ca. 15 DM
    

    Dieser einfache Schaltkreis besteht nur aus wenigen Komponenten.
    Viele Kenner behaupten, er brchte einen satteren Sound, als
    der D/A des Soundblasters.


    Sie bentigen hierzu:

    - 1  IC ZN426E (gibt's z.B. bei CONRAD)
    - 1  10mikro-farad Elektrolyt Kondensator (10V oder mehr)
    - 1  4.7mikro-farad Elektrolyt Kondensator (10V oder mehr)
    - 1  380ohm Widerstand (5%, 1/8W)
    - 1  Stecker fr Ihren Verstrker
    - 1  25 poliger Sub-D Stecker fr den Parallel Port (mnnlich)
    - 1  Stck 10 adriges Kabel oder 10 kurze Kabel
    - 1  5 Volt Stromquelle


                               Zn426e    +5V
    DTyp Pin Nummer\          Ŀ  
                  (2)  D0  Ĵ9     14Ĵ
                  (3)  D1  Ĵ10        
                  (4)  D2  Ĵ11         390
                  (5)  D3  Ĵ12       
                  (6)  D4  Ĵ13     5Ĵ
                  (7)  D5  Ĵ1      6Ĵ       +
                  (8)  D6  Ĵ2      4ĳĴ> zum Verstrker
                  (9)  D7  Ĵ3   7             10F
                               +        (wird meist nicht
                                    4.7F         bentigt)
                                         
                  (25) GND  GND
                                   





    Ein hnlicher Schaltkreis:
    

    Stckliste:

    - 1  DAC-IC Typ ZN428
    - 1  TTL Baustein 7400
    - 1  1mikro-farad Elektrolytkondensator 16V
    - 1  10mikro-farad Elektrolytkondensator 16V
    - 1  390 Widerstand
    - 1  Stecker fr Ihren Verstrker
    - 1  Kabel mit 25 poligem Sub-D Stecker (mnnlich)
    - 1  5 Volt Stromversorgung


       Pin Nr.:       1  3 2               4 5 6 7 8 9 11 20
                                                
                    1 2     LSB     MSB        
                         Ŀ       
                    TTL   Ĵ1      16     
                    7400 Ĵ2  ZN  15    
                       NC Ĵ3  428 14   
                     Ĵ4      13  
                     Ĵ5      12 
                         Ĵ6      11
                       Ĵ7      10Ŀ
               10F     Ĵ8       9    
                                  
                   POTI                       
                   500   İ> 5 Volt
                               390
   zum     <    
   Verstrker             1F
                          
                         



    Mgliche 5 Volt Stromquellen:
    

    +5V vom Gameport abnehmen

    +5V von der Keyboard Buchse abnehmen

    3x 1.5 Volt Batterien (4x 1.3 fr Akkus)

    oder jegliche Stromquelle, welche eine Spannung zwischen 4.5 und 5.5
    Volt erzeugt. Vergessen Sie nicht die Masse Ihrer Stromversorgung
    an die Masse des Schaltkreises anzuschlieen.




    2. Ein noch billigerer D/A Wandler fr ca. 5 DM
    

    Fr den Preis von 20 1% Widerstnden und zweier Stecker knnen
    Sie einen D/A Konverter bauen, der keine Stromquelle bentigt und
    in der Qualitt fast an den oberen Schaltkreis heranreicht.

    Sie brauchen einen Stecker fr Ihren Verstrker und einen fr
    die Parallele Schnittstelle.
    Auerdem 9 20k und 9 10K Widerstnde.
    Benutzen Sie unbedingt 1% Metallschichtwiderstnde!
    20K hren sich besser an, als 22K !

    Parallele Schnittstelle:

          Signal   Pin        20k   20k
          D0       2      >İİ0v
                              20k  10k
          D1       3      >İĴ
                              20k  10k
          D2       4      >İĴ
                              20k  10k
          D3       5      >İĴ
                              20k  10k
          D4       6      >İĴ
                              20k  10k
          D5       7      >İĴ
                              20k  10k
          D6       8      >İĴ
                              20k  10k
          D7       9      >İĴ
                              20k  10k  100nF
                                  Ĵ> Zum Verstrker
                                   10k
          GND      20     >>
                                  0v
          
     Schaltkreis von Harry Stocks.

     Achten Sie bitte wieder darauf, da alle 0 Volt Leitungen
     zusammen gefhrt sind.
     Der 100nF Kondensator wird u. U. nicht bentigt. Lassen Sie
     ihn weg, wenn die Ausgabequalitt schlecht ist.




     3. Ein noch billigerer D/A Wandler fr ca. 3 DM
     

     Parallele Schnittstelle:

     Pin
     2     >İĿ
                  2.8 M    
     3     >İĴ
                  1.4 M    
     4     >İĴ
                  0.7 M    
     5     >İĴ
                  352 K    
     6     >İĴ
                  176 K    
    7      >İĴ
                  88 K     
    8      >İĴ
                  44 K     
    9      >İĴ20uF>zum Verstrker
                  22K
   18      >>zum Verstrker
                                               0V (GND)






  Ŀ
   Achten Sie bei den Widerstnden auf 1% Toleranz und darauf,   
   da es sich um Metallschicht Widerstnde handelt.             
  

    
    4. STEREO-ON-1 BOARD
    

    It is possible to play in stereo with only one parallel port (MODPLAY
    version 2.00 onwards) using the circuit below.  MODPLAY will
    automatically detect this circuit if it is present and work out what
    address it is at  so you can plug it into any of your parallel ports. 
    MODPLAY needs no further options and will default to playing through
    this device.  The +5v supply can be  anywhere between 4.5 and 5.5 volts
    so it could be run from three 1.5v  batteries. (Or from four
    rechargable batteries as these are only 1.2v) 

    * Stereo-on-1 works from MODPLAY 2.03 onwards where it did not in 2.00 *

    You can use your stereo-on-1 board with other programs that require
    a single D/A on the port as follows:

    Find out what address your port is at (LPT1 = 0378, LPT2 = 0278) and
    add 2 (LPT1 = 037A, LPT2 = 027A).  Go into DEBUG and type
    o 37a,0       (replacing 37a with the port address)
    q
    Then all sound directed to the parallel port will come out of both
    channels. 

                                ZN428
                                Ŀ         390
              Ĵ11           6ı+5v
               Ĵ12           7     
                Ĵ13           3NC          
                 Ĵ14                    + 10F
                  Ĵ15           5ĳĶ> Left out
                   Ĵ16                       0v>
      20 >0v       Ĵ1           10+5v  
                     Ĵ2            90v       
      14 >ĳĳĳĳĳĳĳĳĴ4            8        
                                  
      11 >Ĵ          ZN428                   + 1F    
                        Ŀ      Ķ0v
       9 >ĳĳĳĳĳĳĳĴ11 D7   VRIN 6
       8 >ĳĳĳĳĳĳĴ12 D6  VROUT 7 NC
       7 >ĳĳĳĳĳĴ13 D5     NC 3 NC     
       6 >ĳĳĳĳĴ14 D4                 + 10F
       5 >ĳĳĳĴ15 D3    OUT 5Ķ> Right out
       4 >ĳĳĴ16 D2                    0v>
       3 >ĳĴ1 D1     +V 10+5v    
       2 >Ĵ2 D0     0v  90v
       1 >Ĵ4 !EN    0v  8
      25 pin male D connector    


      Notes:

      Make sure all the 0v lines are connected together and connected to the
      0v line of your power source.  Also, make sure the +5v lines are 
      connected together.  The lines marked 'NC' do not need to be connected.  

      If a ZN428 is not available, any D/A with input latches will work -
      the D/A should latch the data bus when pin 4 (!EN) is low.

      ĳ = No connection,  = joined

      The above circuit (Stereo-on-1) is (C) Mark J Cox 1991, 29 Lundie Close
      Stenson Fields, Derby DE2 3AN; and is supplied for personal use only.  
      For any other use, please contact the author at the address above. If 
      this circuit is abstracted or incorporated into any other document or
      circuit then that document or documentation supplied with that circuit
      must contain this paragraph of text.  Any commercial use where not 
      agreed by written contract with the author (Mark J Cox) is prohibited.


     13. STEREO AMPLIFIER
     

     For those of you who have built a stereo DAC and haven't enough
     inputs to your Amplifier - Kenneth Aaron has supplied this
     circuit which is designed to give a high power (11W per channel)
     high quality, low interference, single rail supply amplifier!

      Enable
     >Ŀ    +12v
                    +              
                    10FĿ
           0v        7   13   3    1 Left
      Left     470nF    Ĵ4              2 Speaker
     >Ĵ                  
                        Ĵ5   TDA 7370  14 Right
      Right    470nF    Ĵ11            15 Speaker
     >Ĵ                  
                        Ĵ12              
                    +Ĵ6    8   9    10NC
               47F     
                                   
                      0v

     Make sure that 0v of the +12v supply is connected to all the 0v
     connections on the main circuit.   The enable line has to be tied
     to +12v to 'switch on' the amp


     14. AUTHOR
     

     Before June 1992:
     
     Mark J Cox                 Electronic Mail:
     17 Kirkburn Place                   m.j.h.cox@bradford.ac.uk
     Bradford                    
     W. Yorks, UK               If that fails - try:
     BD7 2BZ                             bc732@cleveland.freenet.edu
                               
     After June 1992:
     
     29 Lundie Close            Check the latest version out!
     Stenson Fields             For a Bradford Address.... after
     Derby, UK                  June!
     DE2 3AN                   



